Cooper M3000 Betriebsanweisung Seite 267
- Seite / 432
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 4 Operation of the Server 4-17
Caution – IMPORTANT - See the following paragraphs for important information about
the domain power-off procedure.
■ When Oracle Solaris OS of the domain is being booted, the power cannot be turned off.
After Oracle Solaris OS booting is completed, execute the poweroff(8) command again.
■ When Oracle Solaris OS of the domain is running in single user mode, the power cannot
be turned off using the poweroff(8) command. Execute the shutdown(1M) command
on the domain.
Note that when Oracle Solaris OS of the domain is running, domain power-off (shutdown
-i5, or equivalent) is required.
Also, even if a system abnormality (like a fan or temperature abnormality) is detected while
the Oracle Solaris OS is being booted, or the system is running in single user mode, there
may be cases where the power cannot be turned off. (An Oracle Solaris OS shutdown is not
executed.) In such cases, immediately perform the procedure above.
4.4.5 Sending a Domain Panic Request
■ Command operation
1. Use the showdomainstatus(8) command to check the power status of the domain
to which a panic instruction is to be issued.
2. Use the reset(8) command to issue a panic instruction to the specified domain.
XSCF> showdomainstatus -a
DID Domain Status
00 Running
01 Running
02 Running
03 Running
<Example> Issue a panic instruction to the specified domain.
XSCF> reset -d 0 panic
DomainID to panic:00
Continue? [y|n] :y
00 :Panicked
*Note*
This command only issues the instruction to reset.
The result of the instruction can be checked by the
"showlogs power".
- SPARC Enterprise 1
- Contents 5
- Contents vii 7
- Contents ix 9
- Preface xi 11
- Audience 12
- Related Documentation 12
- Preface xiii 13
- Text Conventions 14
- Documentation Feedback 15
- XSCF Overview 17
- External Interfaces 18
- Chapter 1 XSCF Overview 1-3 19
- FIGURE 1-1) 19
- RCI Port 20
- USB Port 21
- READY LED 21
- CHECK LED 21
- Serial Port 21
- XSCF-LAN Port (Ethernet Port) 21
- Link Speed LED 22
- UPC Port 22
- SCF Unit (Front) 23
- 1.2 XSCF Functions 25
- XSCF User Account Control 26
- Security 26
- Monitoring 27
- Control Functions 27
- Console Redirection Function 28
- Capacity on Demand Function 28
- Firmware Update Function 29
- Serial Port Connection 31
- XSCF-LAN Ethernet Connection 32
- XSCF-LAN Redundancy 33
- IP addresses, see Chapter 2 35
- 1.4 XSCF User Interfaces 37
- XSCF-LAN 38
- Chapter 1 XSCF Overview 1-23 39
- Setting Up XSCF 41
- About Setup Flow 42
- Chapter 2 Setting Up XSCF 2-3 43
- XSCF> adduser yyyy 44
- XSCF> password yyyy 44
- XSCF> setprivileges xxxxxx 44
- Chapter 2 Setting Up XSCF 2-5 45
- set the DSCP 47
- Chapter 2 Setting Up XSCF 2-9 49
- ■ Log in 54
- 2.2.1 Network Configuration 56
- Network Configuration 57
- TABLE 2-1), Destination 58
- Servers) 60
- TABLE 2-2) 61
- FIGURE 2-1) 61
- Command operation 64
- Configuring XSCF Routing 68
- Making XSCF DNS Settings 69
- User Account Administration 76
- Specifying a User Privilege 80
- Specifying a Password Policy 81
- 2.2.3 LDAP Administration 83
- LDAP Administration 84
- Administration Terms 88
- Setting a user domain 101
- Setting default roles 101
- XSCF> showad defaultrole 102
- Default role: platadm platop 102
- ■ Command operation 103
- Setting timeout 106
- 2.2.5 LDAP/SSL Administration 110
- LDAP/SSL Administration 111
- Administration (Continued) 112
- Before LDAP/SSL settings 113
- 2.2.6 Time Administration 130
- Setting Time and Date 131
- The settings can be enabled 132
- XSCF> showtimezone -c tz 132
- Setting the XSCF Time 134
- Configuring an NTP Server 135
- XSCF> 140
- Term Description 141
- SSH Client 142
- Specifying an SSH Host Key 146
- 2.2.8 Https Administration 149
- Enabling or Disabling Https 152
- Intranet 153
- 2.2.9 Audit Administration 156
- Audit Administration 157
- Specifying the Audit Policy 161
- Displaying the Audit Logs 162
- Log Archiving Administration 163
- Log Archiving 165
- 2.2.11 SNMP Administration 168
- SNMP Administration 169
- Setting SNMPv3 Trap 173
- 2.2.12 Mail Administration 179
- Mail Administration 180
- 2.2.13 Domain Configuration 182
- Domain Configuration Terms 183
- TABLE 2-27 184
- TABLE 2-23 186
- DCL Information 187
- XSB Status Information 188
- Item Explanation 189
- When PSB#n is Uni-XSB type 192
- When PSB#n is Quad-XSB type 193
- Domain Configuration 197
- Displaying the XSB Status 199
- TABLE 2-27.) 204
- TABLE 2-26.) 204
- System Board Configuration 210
- Dividing a PSB Into XSBs 211
- (beginning with XCP 1082) 215
- Operational Modes 216
- Suppression 220
- 2.2.16 Locale Administration 224
- Setting Altitude 225
- Information 229
- Over a Network 231
- Directory Over a Network 232
- Ethernet 235
- 3.2 Types of XSCF Connections 243
- DomainID x 245
- DomainID y 245
- DomainID m 245
- DomainID n 245
- Operation of the Server 251
- XSCF> showenvironment air 255
- Air Flow:63CMH 255
- ■ CPU module information 257
- ■ Memory information 257
- ■ DDC information 257
- ■ I/O unit information 257
- ■ showdcl 259
- ■ showboards 259
- ■ showdomainstatus 259
- ■ version 259
- 4.2.1 Domain Information 260
- ■ setupfru 261
- ■ addboard 261
- ■ deleteboard 261
- ■ moveboard 261
- ■ setdcl 261
- 4.4.1 System Power On 263
- 4.4.2 System Power Off 264
- 4.4.3 Domain Power On 265
- 4.4.4 Domain Power Off 266
- 4.4.6 Domain Reset 268
- 4.7 Changing the Time 276
- 4.8 Switching the XSCF Unit 276
- Administration Terms 277
- Overview of the XSCF Shell 283
- XSCF Commands 284
- XSCF Commands (Continued) 285
- 5.2 Login to XSCF Shell 289
- Password: xxxxxxxx 290
- Commands 294
- ■ showlogs 297
- Message Meaning 300
- XSCF Mail Function 301
- XSCF Email Notification Path 302
- Parts Fault Notification 303
- 6.4 Test Mail 306
- XSCF SNMP Agent Function 307
- 7.2 MIB Definition File 309
- 7.3 About Trap 311
- Trap Issuance 313
- Starting Transmission 314
- ■ Step 3: 315
- Management) 316
- Upgrade of XSCF Firmware and 317
- Maintenance 317
- 1. XCP import 318
- User Interfaces 319
- User Privileges 319
- Firmware Update Environment 320
- Delivering the XCP Files 320
- ■ yy = Minor release number 321
- ■ z = Micro release number 321
- Motherboard unit 324
- Supported Hardware 325
- Firmware Update Tasks 326
- Updating XCP From the Network 327
- XSCF> showlogs monitor 331
- ■ Web browser operation 332
- CMU/MBU Is Added or Replaced 333
- XSCF> version -c cmu 334
- DomainID 0: 02.09.0000 334
- DomainID 1: 02.09.0000 334
- DomainID 3: 02.09.0000 334
- 8.2 Collecting XSCF Logs 338
- Other Logs 340
- Front Panel of the XSCF Unit 342
- How to Use the XSCF Web 345
- outlines each page 346
- Example of the Login Page 347
- Example of the Tree Frame 348
- 9.2 Start the XSCF Web 349
- 9.2.1 Prerequisites 350
- 9.2.2 Supported Browsers 350
- 9.2.4 Specifying the URL 351
- 9.3.1 Logging in to XSCF 351
- 9.3.3 Logging Out From XSCF 352
- 9.4 XSCF Web Pages 353
- Chapter 5 354
- Displaying System Status 355
- Domain Status Display 356
- Device Status Display 356
- System and Domain Operation 357
- Setting System 360
- Menu Function Remarks 361
- Time Settings 362
- SSH/telnet Settings 362
- LDAP Configuration 363
- LDAP/SSL Configuration 364
- Function Remarks 365
- Menu tree 367
- SNMP Configuration 368
- Log Archiving Configuration 369
- Firmware Updating 371
- Log Collection 372
- Component Information 373
- 9.5 XSCF Web Error Messages 374
- A.1 Message Types 375
- ■ Panic message 376
- ■ Console message 376
- ■ Monitoring message 376
- ■ Other notice message 376
- A.2 Messages in Each Function 377
- XSCF Log Information 381
- Information: Notification 382
- B.2 Power Log 385
- B.3 Event Log 387
- B.4.3 Console Log 389
- B.4.4 Panic Log 389
- B.4.5 IPL Log 389
- B.5 Audit Log 390
- B.6 Active Directory Log 392
- B.7 LDAP/SSL Log 392
- XSCF MIB 395
- C.2 Standard MIB 397
- C.3 Extended MIB 397
- C.4 Trap 399
- Troubleshooting 401
- Disconnected 403
- Could Not Add an XSCF User 403
- Other Problems 405
- Being Used 407
- ■ fmdump 408
- Software License Conditions 409
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Cooper M3000
(48 Seiten)
(110 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern