Cooper TS690 Installationshandbuch Seite 22
- Seite / 60
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Pre Power-Up Checks
Once the system is installed, but prior to
powering-up, give the system one final check to
ensure that:
1. The wiring conforms to the requirements
detailed in this manual and that all
interconnections are correct (A to A, B to B
etc.).
2. All system cables are kept clear of mains
supply cables, telephone cables and R.F.
cables. It is recommended that cable ties be
used to keep cables separated.
3. Verify that maximum cable lengths and
resistance's are not exceeded.
4. Mains power supply cables to the system are
connected to an un-switched fused spur.
5. Grommets are used where cables enter metal
housings to ensure that insulation is not
compromised.
ID Cable Checks (TS690ID Only)
Before powering-up the control panel it is
recommended that the following tests are
performed on the ID Loop:
1. Disconnect the two cores of the ID loop from
the control panel [ID LOOP +] and [ID LOOP -]
terminals.
2. Use a DVM to measure the resistance between
the two cores. If the resistance is below 1k
Ohms then there is a short circuit or other wiring
defect on the ID loop. This must be corrected
before going any further. The exact resistance
you measure will depend on the number of ID
devices connected to the ID loop and the
type of DVM that you have. Typical resistance
readings are as follows:
1 device 90K Ohms
10 devices 8.5K Ohms
20 devices 4.5K Ohms
30 devices 2K Ohms
22
System Installation TS690 & TS690ID Installation Manual
RelayRelay
Smoke
Detector
Smoke
Detector
Relay available from
RS components
P/No. 351-982.
Capable of switchin
g
mains voltages
Relay available from
RS components
P/No. 351-982.
Capable of switching
mains voltages
+12V +12V
Aux 12 V
Aux 0V
-ve O/P
+ve O/P
(Programmed as Alarm / Bell / etc)
(Programmed as Alarm / Bell / etc)
(Programmed as Detector Reset)
(Programmed as Detector Reset)
Aux 0V
Aux 0V
Aux 0V
+ve Outputs -ve Outputs
1K0 Ohm Resistor
12V Buzzer
RS Part No. 245-051
12V Buzzer
RS Part No. 245-051
1K0 Ohm Resistor
LED (Light Emiting Diode) LED (Light Emiting Diode)
-Ve O/P
-Ve O/P
-Ve O/P
+ve O/P
+ve O/P
+ve O/P
Aux 12V
Aux 12V
Aux 12V
0V 0V
Diode (IN4001)Diode (IN4001)
Figure 25. Output Examples
- TS690 & TS690ID 1
- Overview 2
- System Installation 2
- Engineer’s Menu 1 2
- Engineer's Menu 2 3
- Appendices 3
- Number of Zones = 8 to 14 5
- Number of Zones = 2 to 38 5
- Supply: 230V ±10% 50Hz 6
- ID Loop Wiring (TS690ID Only) 8
- Cabling Requirements 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- FUSE 315mA 12
- Installation Procedure 13
- Engineer’s Keypad 14
- TS700 LEC Installation 14
- Wiring Detection Circuits 15
- Double Pole 15
- End Of Line 15
- Wiring ID Biscuits 16
- Biscuit Connections 16
- Wiring A Biscuit to a PIR 16
- External Sounder Connections 17
- Auxiliary Tamper 17
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 18
- DC6 Digi-Modem Installation 18
- Regulatory Requirements 18
- Application 19
- Approval 19
- Connections 19
- Installation 20
- DC54 & DC58M Installation 20
- DATAC or RS232 printer 21
- CPA6 Printer 21
- RS232 Data 21
- Pre Power-Up Checks 22
- Initial Power-Up 23
- Power-Up Checks 23
- NVM Defaults 24
- Panel Outputs [1.1] 26
- Digicom Outputs [1.2] 26
- Digicom Channels [1.3] 26
- Programmable Output Types 26
- No Type/Description 27
- Program Circuits [1.4] 29
- Circuit Types 29
- Circuit Attributes 30
- System Timers [1.5] 31
- Setting Modes [1.6] 33
- Do System Print [1.7] 34
- Remote Reset Algorithm [1.8] 35
- Configuration [1.9] 35
- 34 Entry Keypad Lock 38
- 35 Tamp as Burg 38
- 37 Unconf Usr Rst 38
- 38 Keypad PA On 38
- RESET 1.9V to 2.4V 39
- MID 5.6 to 6.4V 39
- HIGH 9.0 to 10.1V 39
- Relearn Hardware [1.C] 40
- StarburstLCD 42
- Change Passcode [2.4] 43
- Chime Circuits [2.5] 43
- Alter Shunt Group [2.6] 43
- Print System Log [2.7] 43
- Configure Part Sets [2.8] 44
- View System Log [2.9] 44
- Log Event Codes 45
- Reset User Code 1 [2.0] 46
- Start Call Back [2.A] 46
- LCD Only 47
- Modem Password 48
- Modem Site No 48
- Program Digicom 48
- Text Editing Keys 50
- Cursor Types 50
- Common Key Sequences 50
- TS690/TS690ID 53
- Setup New Users Flowchart 54
- Engineers Menu 1 55
- Engineers Menu 2 56
- Output Types 56
- Quick Reference User Menus 57
- User Menu 1 57
- User Menu 2 57
- 496804 Issue 1 60
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Cooper TS690
(432 Seiten)
(110 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern