Cooper TS690 Installationshandbuch PDF herunterladen (Seite 55)

Quick Reference Engineers Menus

Engineers Menu 1

key Options Page

1

Program Panel Outputs

1 = Panel Output 1 (relay)

2 = Panel Output 2 (-ve)

3 = Panel Output 3 (+ve)

26

2

Program Digicom Outputs

1 = Channel 1

2 = Channel 2

3 = Channel 3

4 = Channel 4

5 = Channel 5

26

3

Program Digicom Channels

1 = Channel 1 5 = Channel 5

2 = Channel 2 6 = Channel 6

3 = Channel 3 7 = Channel 7

4 = Channel 4 8 = Channel 8

26

4

Program Circuits & Attributes

Circuit Types Circuit Attributes

0 = Not Used 1 = Access

1 = Night 2 = D Knock

2 = 24 Hour 3 = Test

3 = PA Silent 4 = Omit

4 = PA Audible 5 = Reset

5 = Fire 6 = Monitored

6 = Auxiliary 7 = Entry

7 = Final Exit 8 = Chime

8 = Exit Term. Lock Switch Attributes

9 = Keyswitch F,A,B,C = wards

L = Lockset

M = Momentary

I = Inverted

29

5

System Timers

00 = Abort Delay 12 = Monitor Dur.

01 = No Rearms 13 = Pset Bell Dly

02 = Settle Time 14 = Courtesy Dur.

03 = Pset Com Dly 15 = No Rem. Resets

04 = Exit time 16 = Modem Rings

05 = Entry Time 17 = CID Alarms

06 = Bell Dur. 18 = AC Off Delay

07 = Bell Dly 19 = Test Call

08 = Double Knock 20 = Confirmation

09 = Test Time 21 = Line Fault Dly

10 = 2nd Entry 22 = Service Time

11 = Part Set Entry 23 = Test Call At

31

6

Setting Modes

0 = Full Set 1 = Final Exit

A = Part Set A 2 = Exit Terminator

B = Part Set B 3 = Timed Exit

C = Part Set C 4 = Instant

5 = Deferred

6 = Lock set

33

7

System Print-Out

33

8

Remote Reset Algorithm

Enter Algorithm number 004 - 199.

34

key Options Page

9

System Configuration

No. Yes No

00 = Bell is an SAB Bell is an SCB

01 = User 1 Limited User 1 Unlimited

02 = Fire Signals All Fire Signals Set

03 = Silent 24hr Ccts Audible 24hr Ccts

04 = Enable Duress Disable Duress

05 = Invert Abort O/P Normal Abort O/P

06 = Set with LF Can’t Set with LF

07 = User Reset Engineer Reset

08 = Extended Format Fast Format

09 = Hi-Sec Engineer Lo-Sec Engineer

10 = Tamp User Reset Tamp Engr Reset

11 = Do Battery Test No Battery Test

12 = F.Exit Is Night F.Exit is Normal

13 = User Code + ENT User Code Only

14 = Show P.Set Info Show Time Only

15 = Dial Consecutively Dial Alternatively

16 = Set with AC Off No Set with AC Off

17 = Loud Chime Normal Chime

18 = Invert O/P 1 Normal O/P 1

19 = Invert Digi O/Ps Normal Digi O/Ps

20 = Online Keypad No Online Keypad

21 = Restore PID PID Alarms Only

22 = User Authorised No Authorisation

23 = Mimic Alm & Flt Mimic Alarm Only

24 = Monitor Off Hook Monitor Line Cut Only

25 = Answerphone Def. Normal Answer

26 = Send Open/Close No Open/Close

27 = Tampers always Tampers when set

28 = 24hr ccts always 24hr ccts when set

29 = Keypad PA Silent Keypad PA Audible

30 = Snders on Confirm Sndrs on First Alarm

31 = Bells on Confirm Bells on First Alarm

32 = Conf after Entry No Conf After Entry

33 = Confirmation On Confirmation Off

34 = Entry kpd locked Entry kpd free

35 = TA as Burg TA as TA

36 = Ent. conf after 2cct After 1 cct

37 = Unconf Usr Rst Unconf Eng Rst

38 = Keypad PA On Keypad PA Off

34

0

Go To User Menu 1

36

A

Add/Clear ID Devices

A = Add ID Devices

B = Toggle ID Status and View Circuits Mode

C = Clear and Learn all ID Devices

0 = Toggle SLOW SCAN Mode and Normal

37

B

View Location Text

37

C

Re-Map ID Devices & Relearn Hardware

Re-Map ID Devices (TS690ID Only)

1. Enter Device No 01 - 30 then ENT.

2. Enter Circuit No 01 - 38 then ENT.

3. Repeat for other devices.

Relearn Hardware

Clears the “RELEARN REQUIRED” / ”RESET

CONFIG” message and logs all devices on to

system.

38

55

TS690 & TS690ID Installation Manual Appendices

1 2 ... 50 51 52 53 54 55 56 57 58 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare